Reliable, uninterrupted power and data loss protection is a crucial to sensitive medical equipment in hospitals and healthcare facilities.

Medical UPS are designed to meet these requiprement and meet stringent safety standards and regulations

     
         

OMNIX350HG
OmniSmart 230V 350VA 225W CE/IEC 60601-1 Medical Grade Line-Interactive UPS with Built-In Isolation Transformer
 

SMX1200XLHG
SmartPro 230V 1kVA 750W Medical-Grade Line-Interactive Tower UPS with 6 Outlets, Full Isolation, Expandable Runtime
 

SMX1200XLHGL
SmartPro Medical-Grade UPS, Line Interactive, Lithium Battery, 6 Outlets - 230V, 1kVA, 750W, Full Isolation

Tripp Lite's OMNIX350HG offers medical-grade UPS protection with built-in line interactive voltage regulation. IEC320 plug & outlets, plus built-in isolation transformer with Faraday shield offers full isolation and removes common mode noise. Tested to CE/IEC 60601-1 as medical electrical equipment. 350VA power handling capacity supports computers, inter-networking equipment and other critical loads during commercial power failures. Line interactive voltage regulation corrects brownouts as low as 159V back to normal 230V levels, saving battery reserves for use only during complete power failures. Includes, 2 line phone surge suppression and built-in USB communications port.

Application Usage
This UPS contains a lead acid battery designed to be connected continuously to an AC power source, except during brief power outages. It is not intended for frequent charge/discharge cycles, such as mobile cart applications where the UPS is often disconnected from the power source. Using the OMNIX350HG in this type of application will void the battery warranty.

Features
Ideal UPS protection for applications in medical patient-care areas where CE/ IEC 60601-1 electrical medical equipment is required
Line-interactive voltage regulation corrects brownouts as low as 159V without using battery power
IEC320 plug and outlets offer added degree of safety and reliability to input/output connections
Full line isolation prevents shock potential and operational problems in sensitive electronic equipment
Resistant to electrostatic discharge
Supports loads up to 350VA/225 watts
37 minutes half load runtime (with 175VA load), 15.5 minutes full load runtime (with 350VA load)
6 protected outlets; 6-inch dongle with IEC C14 inlet
C14 inlet accepts user-supplied AC power cord with grounded country-specific plug
1-USB port for monitoring interface
Complete surge protection, line isolation and EMI/RFI noise filtering
2 phone line surge suppression for modems, fax machines and other phone accessories
4 diagnostic LEDs indicate AC present, on battery, voltage correction & battery low/replace
Battery replacement door and back panel equipotential connection (grounding lug)
Ground Potential Equalization Connector: POAG-S6/20

Package Includes
OMNIX350HG Hospital Grade UPS System
USB communication and telephone cables included
Warranty information
Instruction manual

 

Tripp Lite’s SMX1200XLHG medical-grade UPS system provides dependable battery backup and is fully compliant with UL 60601-1 regulations when plugged into a hospital-grade outlet, making it ideal for use in patient-care vicinities. The 1kVA/750W capacity provides up to 27.5 minutes of runtime for a half load, or 11 minutes for a full load so you can work through short power failures and perform an orderly system shutdown in a prolonged blackout.

Built-in line-interactive voltage regulation corrects brownouts as low as 155V and overvoltages as high as 274V to normal 230V nominal output, without drawing battery power. The SMX1200XLHG’s built-in isolation transformer with Faraday shield offers full isolation and removes common mode noise while maintaining full AC surge suppression in all modes. Cumulative leakage current of all connected equipment is less than 100 microamps.

This UPS system features six IEC320 C13 hospital-grade outlets and has a hospital-grade IEC320 C14 plug on a 15 cm (6 in.) dongle. All six outlets provide both backup protection and surge protection, rated to 340 joules.

The SMX1200XLHG also features diagnostic LEDs, as well as a USB port and a DB9 serial port that work with Tripp Lite’s included PowerAlert software for safe, unattended system shutdown and file saves in the event of a prolonged power failure.

Features
Provides Ideal UPS Backup in Healthcare Facilities
-Compliant with UL 60601-1 standards for use in patient-care vicinities, when plugged into a hospital-grade outlet
-Built-in isolation transformer with Faraday shield offers full isolation and removes common mode noise

Battery Backup and Full Surge Protection
-27.5 minutes runtime for half load (375W); 11 minutes for full load (750W)
-All six hospital-grade outlets provide surge protection rated to 340 joules
-EMI/RFI noise filtering ensures equipment runs smoothly without line noise interference
-Resistant to electrostatic discharge

LEDs and Audible Alarms Keep You Aware of Power Status
-Indicator lights on the front of the unit show you when the UPS is on and supplying utility power, when operating in voltage correction mode or in battery mode, relative load level and low-battery warning
-Audible alarms alert you to power failure, overload and low battery conditions; the alarm’s mute/quiet mode ensures patients are not disturbed

Saves Your Files, Even When You’re Away
-Works with Tripp Lite PowerAlert software (included) to enable safe, unattended system shutdown and files saves during prolonged power failures
-Connects to your computer via either the DB9 port or USB port

 

Line-interactive UPS provides basic battery backup with UL 60601-1 compliance for use in medical facilities, including patient care areas.
Lithium battery backup allows time to save files and safely shut down during blackouts
6 C13 hospital-grade (HG) outlets provide power to medical equipment
UL 60601-1 compliant for use in patient care vicinities when plugged into HG wall outlet
Alarm and front-panel LEDs report online, battery, fault and overload conditions
10,000-cycle LiFePO4 battery lasts up to 30x longer than comparable SLA batteries
2-year limited warranty

Typical Applications
Protect your medical electronics against power surges, brownouts and blackouts in patient care vicinities
Operate essential equipment during short-term power outages using battery backup power
Shut down PCs, monitors, mobile medical components and other equipment without data loss during long-term power outages


Package Includes
SMX1200XLHGL 1kVA/750W SmartPro Medical-Grade UPS, Tower
USB monitoring cable, 1.8 m (6 ft.)
DB9 serial monitoring cable, 1.8 m (6 ft.)
Owner’s manual


 

SMX700HG
SmartPro 230V 700VA 450W Medical-Grade Line-Interactive Tower UPS with 6 Outlets, Full Isolation, USB, DB9
 

 

SMX700HGL
19” Fanless Intel® Medical SmartPro Medical-Grade UPS, Line Interactive, Lithium Battery, 6 Outlets - 230V, 700VA, 450W, Full Isolation
 

Features
Provides Ideal UPS Backup in Healthcare Facilities
Compliant with UL 60601-1 standards for use in patient-care vicinities, when plugged into a hospital-grade outlet
Built-in isolation transformer with Faraday shield offers full isolation and removes common mode noise

Battery Backup and Full Surge Protection
-36 minutes runtime for half load (225W); 14.5 minutes for full load (450W)
-All six hospital-grade outlets provide surge protection rated to 340 joules
-EMI/RFI noise filtering ensures equipment runs smoothly without line noise interference
-Resistant to electrostatic discharge

LEDs and Audible Alarms Keep You Aware of Power Status
-Indicator lights on the front of the unit show you when the UPS is on and supplying utility power, when operating in voltage correction mode or in battery mode, relative load level and low-battery warning
-Audible alarms alert you to power failure, overload and low battery conditions; the alarm’s mute/quiet mode ensures patients are not disturbed

Saves Your Files, Even When You’re Away
-Works with Tripp Lite PowerAlert software (available as a free download) to enable safe, unattended system shutdown and files saves during prolonged power failures
-Connects to your computer via either the DB9 port or USB port

Package Includes
SMX700HG 700VA/450W Medical-Grade Tower UPS System
USB monitoring cable, 1.8 m (6 ft.)
DB9 serial monitoring cable, 1.8 m (6 ft.)
Owner’s Manual

 

Line-interactive UPS provides basic battery backup with UL 60601-1 compliance for use in medical facilities, including patient care areas.
Lithium battery backup allows time to save files and safely shut down during blackouts
6 C13 hospital-grade (HG) outlets provide power to medical equipment
UL 60601-1 compliant for use in patient care vicinities when plugged into HG wall outlet
Alarm and front-panel LEDs report online, battery, fault and overload conditions
10,000-cycle LiFePO4 battery lasts up to 30x longer than comparable SLA batteries
5-year limited warranty

Typical Applications
Protect your medical electronics against power surges, brownouts and blackouts in patient care vicinities
Operate essential equipment during short-term power outages using battery backup power
Shut down PCs, monitors, mobile medical components and other equipment without data loss during long-term power outages

Package Includes
SMX700HGL 700VA/450W SmartPro Medical-Grade UPS, Tower
USB monitoring cable, 1.8 m (6 ft.)
DB9 serial monitoring cable, 1.8 m (6 ft.)
Owner’s manual

 
         


Security II Medical UPM
 

Security Plus Series (UPS)
 

3200 Series UPS

If you think a UPS is the ultimate in power protection, we`ve got some news for you: Our Security II Medical UPM, or Uninterruptible Power Manager, performs functions which your UPS never dreamed of.

For medical systems used in the vicinity of a patient (or anywhere that low leakage current is required), our medical UPMs are the perfect solution for providing conditioned, uninterruptible power.

North American models are listed to UL60601-1 3rd edition with RA and cUL22.2 No. 60601-1 and are suitable for patient vicinity applications. International models are listed to IEC60601-1 3rd edition with RA and are CE marked. All models reduce connected equipment leakage current to less than 300 µamps

All North American models have UL and cUL listings. International models are safety-agency listed and carry the CE mark.
Product sizes range from 420 VA to 3000 VA
0.9 Output power factor with true sine-wave output
Low impedance isolation transformer and line interactive operation
UL60601 3rd Edition with Risk Assessment
UL17785thEdition
True VA Management
AdvancedSNMPCommunicationCapability
User-FriendlyGUIInterface andDiagnostics
Auto BatteryTest and User hot-swappable battery
Over temperature protection and alarm
Switchable outlets via software
Meets FCC Class A (optional Class B available)
Meets NEMA, FAA, and DOT guidelines for transportation of UPS batteries
Let through voltage is less than 10 volts normal mode and less than 0.5 volts neutral-to-ground when tested to ANSI/IEEE C62.41
POWERVAR`s five-year warranty (two-year on batteries) on parts and labor provides complete peace of mind

 

Oversizing a power protection system can result in higher costs to buy, install and operate. With the Security Plus Series UPS from AMETEK Powervar, you do not have to oversize your equipment.

The Security Plus Series is built to handle modern computer loads – systems with high crest factors and high current inrush peripherals – so over sizing is never an issue. In turn saving you money on your power protection equipment investment.

Security Plus offers custom solutions to meet the electrical requirements in today’s most diverse environments. You have the ability to custom design the output receptacle panel and your input line cord. These options allow the Security Plus Series to offer quick and easy on-site connection to your equipment.
All models are UL listed and CE marked.
Product sizes range from 2 kVA to 15 kVA
Wide input voltage and frequency window provided by the online inverter
Impressive 0.9 output power factor
Low impedance isolation transformer
Low input THDi
Industry leading overload capabilities
Diverse input voltage options

Let through voltage is less than 10 volts normal mode and less than 0.5 volts neutral-to-ground when tested to ANSI/IEEE C62.41

Powervar’s three-year warranty (two-year on batteries) on parts and labor provides complete peace of mind.

 

The 3200 Series Three-Phase Uninterruptible Power Supply (UPS) is designed for small data centers and critical load applications.

AMETEK Powervar 3200 Series’ reliability and superior design has one of the smallest footprint in the industry which translates to more data center space for additional computer racks.
300% overload – sustain for 10 seconds online
High-efficiency rate, up to 93%
Product sizes range from 10 kVA to 40 kVA
The most advanced IGBT technology, wide input voltage range
All models are UL and cUL listed.
Front and top access for serviceability
Integrated SNMP network card and Modbus ports to remotely monitor and manage the UPS system
Two-year warranty (includes batteries)

Accessories:
Matching Transformer Cabinets
Matching Extended Battery Cabinets
Matching Maintenance Bypass Systems
DC Disconnects
Wall- mounted external Maintenance Bypass Systems
Remote Monitoring Panel (RMP)
SEISMIC/OSHPD Approved


3400 Series UPS
 


 Security II Rackmount Medical UPM
   

Imagine power protection that keeps your business running continuously, at peak efficiency, with lower costs, and remote system monitoring – all within one of the smallest footprints in the industry.

Powervar's 3400 Series Three-Phase UPS does just that.

Designed to meet the uptime demands of mid-sized mission-critical facilities, the 3400 boasts the latest IGBT technology and 96.3% efficiency (AC to DC). The space-saving design translates to more data center space, additional computer racks, and overall operational savings.

Features:
The most advanced three-step IGBT's in the industry
300% overload capacity - sustain for 240 msec online
High-efficiency rate, up to 96.3%
Product sizes range from 80 kVA to 125 kVA
Wide input voltage range: +15 / -20%
Convenient front access for serviceability
Remotely monitor and manage UPS with integrated SNMP network card and Modbus
All models are UL and cUL listed
Two-year warranty (includes batteries)

Accessories:
Matching Transformer Cabinets
Matching Extended Battery Cabinets
Matching Maintenance Bypass System Cabinets
DC Disconnects
Wall- mounted external Maintenance Bypass Systems
Remote Monitoring Panel (RMP)
Power Distribution

 

 If you think a UPS is the ultimate in power protection, we’ve got some news for you: Our Security II Rackmount Medical UPM, or Uninterruptible Power Manager, performs functions which your UPS never dreamed of.

Why settle for backup power alone when the AMETEK Powervar Security II Rackmount Medical UPM lets you protect your equipment from all power viruses? Thanks to its low impedance isolation transformer, this UPM delivers clean, fully conditioned power which is free from noise, voltage spikes and common-mode disturbances. If the power goes out, backup power is only one of the many benefits you will receive.
All North American models have UL and cUL listings. International models are safety-agency listed and carry the CE mark.
Product sizes range from 700 VA to 1440 VA
0.9 Output power factor with true sine-wave output
Low impedance isolation transformer and line interactive operation
UL60601 3rd Edition with Risk Assessment
UL 1778 5th Edition
True VA Management
Advanced SNMP Communication Capability
User-Friendly GUI Interface and Diagnostics
Auto Battery Test and User hot-swappable battery (non medical units only)
Meets FCC Class A (optional Class B available)
Meets NEMA, FAA, and DOT guidelines for transportation of UPS batteries

Let through voltage is less than 10 volts normal mode and less than 0.5 volts neutral-to-ground when tested to ANSI/IEEE C62.41

POWERVAR’S five-year warranty (two-year on batteries) on parts and labor provides complete peace of mind.

   

 

Talk to a MasTec Sales Engineer

   
© MasTec Ltd 1997- 2019